Question 1

How to Cut SUNLITE Multiwall Polycarbonate Roofing Panels?

Accepted Answer

Multiwall polycarbonate sheets are strong, durable, lightweight, and provide excellent thermal insulation. These features make them ideal for professionals and DIY enthusiasts alike. On-site tailoring and trimming is simple. Follow these guidelines to ensure quality results.

Safety First: Protect yourself by using professional equipment, keeping your surroundings neat and tidy, and using tools with caution and care.

Place a layer of cardboard or plywood on the workbench before placing the first sheet. This will protect the surface from scratches.

Place one multi-wall panel on your workbench. You should cut one sheet at a time, and not stack sheets together.

Multiwall polycarbonate sheets come with protective films. This film indicates which side of the panel is UV-protected. Do not remove it. You will need it later.

Use a measuring tape to measure the sheet, and make pen marks at each end. Join the marks with a ruler.

Do not rush measuring and marking. Once trimmed, you cannot patch the sheets together.

Secure the polycarbonate sheet to the workbench surface to prevent movement and vibrations.

Support the sheet near the cutting line. You can do this by placing a timber plank on top of it, parallel to the markings.

Cut along the marked pen line. The preferred method is to use a fine-tooth saw that rotates at high speed.

Advance the saw slowly and steadily and do not stop once you have begun. It will ensure a clean, consistent edge.

Clean the sheet’s channels with compressed air.

Remove leftover cuts and scraps from the cutting table.

Question 2

What size do bullet resistant polycarbonate sheets come in?

Accepted Answer

PALSHIELD ballistic grade polycarbonate is available in a variety of sizes and specifications. Custom size options are available upon request.

Question 3

How to cold bend flat plastic sheets?

Accepted Answer

Industrial plastic sheets can be cold bent or curved, within their minimal permitted bending radius, without damaging their mechanical performance. The minimal permitted bending radius for a plastic sheet is a factor of its thickness.

A simple way to calculate the allowed cold bend radius is to multiply the sheet's thickness by 200. For example, for a 5mm sheet the arch radius should not be less than 1000mm (5X200).

Question 4

What kind of drill do you use for solid plastic sheets?

Accepted Answer

Regular, high-speed steel twist drills, or carbide-tipped drills are suitable for drilling holes in PALSUN sheets of various thicknesses, as long as they are sharpened well. They are used for bores up to 12 mm in diameter.

Larger holes may be drilled with flat, chisel edged drill blades with a triangular cutting tip, similar to those used in woodworking, kept sharp.

Rake angle should be about 5° to avoid side friction. They are used for bores from 12 to 20mm. Commercially available cutting cups or circle cutters of several types can be used for large round apertures.

Reduce the drill speed for large diameter holes or large gauge plastic sheets.

For detailed specifications and drilling tips and recommendations, look up the fabrication guide in the downloads section.

Question 5

How to CNC route solid plastic sheets?

Accepted Answer

Regular, high-speed steel twist drills, or carbide-tipped drills are suitable for drilling holes in PALSUN sheets of various thicknesses, as long as they are sharpened well. They are used for bores up to 12 mm in diameter.

Larger holes may be drilled with flat, chisel edged drill blades with a triangular cutting tip, similar to those used in woodworking, kept sharp.

Rake angle should be about 5° to avoid side friction. They are used for bores from 12 to 20mm. Commercially available cutting cups or circle cutters of several types can be used for large round apertures.

Reduce the drill speed for large diameter holes or large gauge plastic sheets.

For detailed specifications and drilling tips and recommendations, look up the fabrication guide in the downloads section.

Question 6

How to cut solid flat plastic sheets?

Accepted Answer

A variety of power saws, either table mounted or portable can be used to saw polycarbonate and PVC solid sheets.

A moving table, fixed blade bench saw is preferable for long, straight sawing.

Radial arm saws are generally used for “cross-cut” (width) or diagonal sawing.

Handsaws are slower and less accurate than table saws. These can be used for on-site trimming.

Laser or water-jet cutting is possible when cutting polycarbonate sheets, but not recommended for PVC sheets.

For detailed saw blade specifications, clearance angle, and detailed information, look up the product's fabrication guide in the downloads section.

Question 7

How to mechanically fasten plastic sheets?

Accepted Answer

Flat, solid plastic sheets such as PALSUN, PALCLEAR or PLOPAQUE can be fastened with nuts and bolts, provided several points are remembered:

Use EPDM and aluminum washers to distribute the load.

Do not use rivets, as they apply excessive force and cause sheet cracks.

Drill a slightly oversized hole by 2-3 mm, and tighten moderately.

When using mechanical fasteners, they should be evenly spaced to avoid stress accumulation at particular points.

Wherever possible, a floating frame, or H profile installation is preferable, similar to glass, and without mechanical drilled fasteners.

Question 8

How to store flat  plastic sheets?

Accepted Answer

Flat plastic sheets, either solid or foamed, should be transported and stored horizontally, on a flat, sturdy pallet whose dimensions are equal or larger than the largest of the sheets.

The sheets should be secured to the pallet during transportation and on-site handling.

It is recommended to stack the sheets with the longer sheets at the bottom and the shorter on top, leaving no unsupported overhang.

Palram's products leave the factory in packages, wrapped in white, watertight film. The wrapping should be removed as close to use as possible.

Avoid leaving sheets stored unwrapped. Dirt may accumulate on the sheets and/or their edges, attracted by electrostatic charges in the sheets

Sheets should be stored in a covered, dry, ventilated place away from direct sunlight.

If storing sheets temporarily in an open area, cover the entire pallet with a white opaque film, sheet, cardboard or any other protective material.

Question 9

Are PVC sheets recyclable?

Accepted Answer

All of Palram's PVC sheets are REACH and RoHS compliant, and are 100% recyclable.

Depending on local regulations and facilities, recycling options may vary. It is possible to recycle PVC sheets mechanically or chemically.

Because of its recyclable properties, it can be reformed into new products.

While minimizing environmental impact, this increases the product's life cycle and reduces waste.

Question 10

Are PVC sheets water-resistant and chemical-resistant?

Accepted Answer

Yes, PVC sheets are highly resistant to moisture and chemicals. They can withstand rain and repeated cleaning without warping or cracking.

Question 11

How to laminate PVC sheets?

Accepted Answer

Depending upon the type of application and the equipment available, the techniques recommended for lamination of PALBOARD multilayered panels or PALIGHT foam PVC are cold press using adhesive-backed paper, cold vacuum press, hand laminating with transfer adhesive, and using spray adhesive.

None of these processes involve heat. Because PVC may warp at temperatures above 65°C or when heated from one side only.

For ideal results, the sheet should be cleaned with isopropyl alcohol, and allowed to dry, prior to adhesion. When laminating with pressure-sensitive adhesives, a force of 25–40 psi is required. Proper spacers are also critical. Because force must be applied equally across the material.

For further information, download the Product Fabrication Guide in the downloads section.

Question 12

Is PVC suitable for UV printing / UV curing?

Accepted Answer

PVC is a good substrate for UV inks.

Wide format and flatbed printers employ various ink and ink curing technologies to allow high quality printing at high speeds.

PALIGHT is suitable for use with UV curing and solvent-based digital inks, and for IR drying when water-based inks are required. It retains superb whiteness, even after intense UV curing.

UV Screen Printing Inks also work well on PVC. The most critical factor to consider when using UV systems is the curing oven. Low-wattage bulbs should be used to keep temperatures below 65°C. UV curing systems with variable speed conveyors are ideal.

Question 13

How to screen print on PVC sheets?

Accepted Answer

Screen printing on PVC sheets is simple.

It is recommended to consult the ink manufacturer regarding required ink additives for proper adhesion. In addition, it is recommended to test screen printing inks before production begins.

Before screen printing, the sheet's surface should be cleaned with isopropyl alcohol and a clean white cloth.

To remove small scratches or dents, fan a heat gun over the affected area. However, do not overheat, to avoid surface deformation.

After printing is completed, screen printing ink should air dry, rather than heat dry.

For further information, download the Product Fabrication Guide in the PALIGHT Downloads section.

Question 14

How to paint PVC sheets?

Accepted Answer

There are a variety of paints that can be used on PVC sheets.

Some examples of suitable paints include vinyl, acrylic lacquers, and two-part polyurethanes.

Before painting, the sheet's surface must be dry, clean, and grease-free.

When applying dark color paint to PVC sheets intended for outdoor use, it is imperative that the paint has a light reflectance value of 55 or higher in order to avoid excessive heat absorption, which will result in deformation.

For further information, download the Product Fabrication Guide in the PALIGHT Downloads section.

Question 15

How to heat-bend PVC sheets?

Accepted Answer

PVC sheets such as PALIGHT, PALABOARD, PALCLEAR and PALOPAQUE, can be bent with Calrods, radiant heaters, strip heaters or air-circulated ovens. Heat guns can also be used in small areas.

To ensure successful results, a thermostat should be employed to regulate the sheet temperature so that the surface temperature does not exceed allowed limits.

When using a metal contact strip heater, cover the heater strip with Teflon spray to prevent marking the sheets.

Different sizes of rectangular heating bars can be applied to produce bends of different radius. The larger the heated area of the sheet, the broader the radius can be created.

When heat-bending PVC sheets at a gauge thicker than 4 mm, the sheet should be warmed from both sides.

PVC sheets require heating approximately 30 to 40 seconds per millimeter prior to being bent.

To form tighter bends with smaller radii, use a small heated area on the upper surface (inside the bend) of the sheet and a larger heated area on the bottom surface (on the outside of the bend) of the sheet.

A minimum radius of twice the sheet thickness is necessary to avoid breakage.

When bending PVC sheets into an angle, the extension of the sheet on either side of the angle should be at least 20 times the panel thickness.

Once heat-bent, place the panel to cool down in a fixture, such as a jig or clamp. Fans and/or compressed air will speed up cooling. For detailed guidance, look up the Product Fabrication Guide in the Downloads section.

Question 16

Are PALIGHT and PALBOARD sheets suitable for outdoor use?

Accepted Answer

Yes, both PALIGHT foamed PVC sheets and PALBOARD multylayered sheets are suitable for outdoor use. However, it's essential to select the appropriate thickness and grade for prolonged exposure to direct sunlight and heat.

Question 17

How to make a V-groove in PALBOARD?

Accepted Answer

V-grooving PALBOARD is an excellent method that helps industrial designers turn a 2D panel into a 3D object.

For V Groove Milling\Routing, use a machine bit designed for bending applications. Such bits offer top angles of 90°, 120° or 135°.

A 90° bit produces rectangular bends with almost no gaps.

120° or 135° rounded tip bits produce acute angled bending of up to 90° with approx. 2 mm gap between the sides.

Make sure not to route through the PALBOARD panel. Leave 0.6 mm to 0.8 mm, so you can benifit from the structural strength of this matrial.

Question 18

Can PVC foam sheets and PALBOARD panels be routed?

Accepted Answer

PALBOARD and PALIGHT sheets can be routed using multi-fluted carbide tools on standard woodworking routers. Standard tools and machines can be used without altering equipment. Adjust feed and speed rates as needed to achieve the most precise edge finish.

Using standard milling machines, follow these guidelines:

Relief angle: 5° to 10°

Rake angle: -10° to 0°

Cutting speed: up to 18,000 RPM

Cutting feed: 0.3-0.5 mm / revolution

Question 19

What drill bit do you use for PVC foam or for PVC multilayered sheet?

Accepted Answer

PALIGHT and PALBOARD can be drilled with carbide-tipped bits using metal twist drills.

The following settings are recommended:

Point angle: between 90° and 110°

Spiral angle: 30°

Cutting speed: 1000 - 3000 RPM

Feed rate: 0.2 - 0.5 mm / revolution

The minimum distance from the edge should be 2 times the hole diameter.

To reduce heat build up when drilling thick gauge sheets, it may be necessary to periodically remove the drill bit from the material.

Question 20

How to cut PVC foam or PVC multilayered sheet?

Accepted Answer

PALBOARD and PALIGHT sheets up to 3 mm thick can be cut with a utility knife or blade.

A jigsaw with rough-cut blades designed for plastics can also be used. Smooth metal cutting blades are not recommended.

Another manual option is table top or vertical cutters. In such cases, it is recommended using cutters with twin wheel head blades suitable for cutting ACP (Aluminum Composite Panel).

For industrial volumes, use a bridge saw or a circular table saw.

Saw blade specifications, clearance angle, and detailed information are available in the Product Fabrication Guide in the downloads section.

Question 21

Is PALRUF resistant to UV radiation?

Accepted Answer

Yes, PALRU corrugated PVC roofing sheets are UV resistant.

Question 22

Can I use PALRUF clear PVC corrugated sheets for industrial skylights?

Accepted Answer

PALRUF is an excellent skylight panel. It can overlap corrugated metal sheets and other types of corrugated roofing panels. PALRUF skylights are resistant to chemicals and fumes, and are an ideal solution for the chemical industry.

Question 23

Can I install PALRUF corrugated PVC and SUNTUF corrugated polycarbonate sheets horizontally for siding?

Accepted Answer

Yes. Make sure you start installing from the bottom up so overlaps prevent water from penetrating indoors.

Question 24

How to Store PVC Sheets

Accepted Answer

PVC sheets are durable and chemically resistant and guaranteed to last for many years if handled properly.

Here are some tips for storing PVC sheets to ensure you get the most out of your investment.

Store your PVC sheets horizontally on a flat surface, such as a pallet or a shelf.

Ensure that no nails or bolts protrude from the platform. Even small rocks can leave permanent dents and scratches on the sheets.

Stack the largest sheets at the bottom, and the shorter, smaller panels on top.

Avoid stepping on PVC panels and placing heavy or sharp equipment on them.

Ensure that the PVC sheets are stored in a dry, ventilated, cool, shaded area away from direct sunlight.

Do not stack transparent or translucent sheets over opaque PVC sheets.

Avoid covering the sheets with dark films or other heat-absorbing materials.

Cover the panels with an opaque, bright, waterproof cover if you intend to leave them outdoors.

Keep your stack dry to prevent whitening and water spots.

Question 25

What is the best polycarbonate panel for thermal properties and light transmission?

Accepted Answer

There is a trade-off between light transmission, transparency, and thermal properties in polycarbonate sheets. Multiwall polycarbonate sheets provide superior thermal insulation over solid sheets, but they are translucent, not transparent.

Clear polycarbonate panels will be fully transparent, but less thermally insulating.

Both options allow high light transmission, depending on their color.

If your main concern is light transmission, and not a glass-like appearance, you can achieve that with multiwall sheets, such as SUNLITE, or with the SUNPAL architectural multiwall panel system.

If your main concern is clarity, your best option is PALSUN solid polycarbonate sheets, or SUNGLAZE architectural solid panel system.

Another important factor to remember is that multi-wall sheets weigh significantly less than solid sheets. This can lower your construction and labor costs.

Question 26

Which side of SUNLITE roofing sheet should face up?

Accepted Answer

SUNLITE multiwall polycarbonate sheets are provided with a protective masking film that indicates which side is shielded from UV.

It is critical to install the sheets with the UV-protected side facing up.

Remove the marking strip after installation.

Question 27

What structural support is needed for SUNLITE polycarbonate sheets?

Accepted Answer

SUNLITE roofing support depends on several factors:

Support type: Some architectural projects may use four-sided clamps or frames, two-sided clamped glazing, or two-way clamped arched glazing. DIY and home renovation projects typically use purlins to support the roof.

Expected wind and snow loads should also be considered based on local building codes.

The SUNLITE Technical Guide in the downloads section contains a detailed tables for all scenarios.

Question 28

What is the best roof pitch for SUNLITE DIY polycarbonate sheets?

Accepted Answer

A proper slope keeps water off the roof. It prevents leaks, keeps the roof clean, and ensures structural integrity.

Roof slope percentage indicates how much the roof falls over a given distance.

SUNLITE multiwall polycarbonate sheets require a 10% minimal slope.

This means a drop of at least 10 centimeters over one meter.

If you expect leaves or snow to accumulate on your roof, consider a deeper slope.

Question 29

Can SUNLITE multiwall polycarbonate sheets be bent into arches?

Accepted Answer

SUNLITE sheets may be cold bent or curved. There is only one rule: stay within the allowed arch radius. Curving SUNLITE sheets beyond the permitted radius induces undue stresses and strains, causing premature failure.

The minimum bending radius is determined by the cell structure and thickness.

For example, the allowed bending radius of SUNLITE 8mm twin-wall is 1,400mm, while the allowed bending radius of SUNLITE 25mm X-Lite is 5,000mm.

The SUNLITE Technical Guide in the downloads section contains a detailed Arching Radius table for the complete SUNLITE range.

Question 30

What is the right saw for on-site cutting SUNLITE multiwall polycarbonate sheets?

Accepted Answer

Safety First: Protect yourself by using professional equipment, keeping your surroundings neat and tidy, and using tools with caution and care.

Power tools

Circular table saws are the most efficient and accurate way to cut plastic sheets. This option, however, isn't always available on home renovation sites.

A portable fine-toothed circular saw is ideal for cutting on-site. High blade speed and a moderate feeding rate will give you the most effective results.

A jigsaw also produces clean, accurate cuts, but requires better control. It is most suitable for cutting complex shapes and curved lines.

Manual tools

Working with manual tools is time-consuming, but it reduces the risk of sheet damage.

Manual handsaws or hacksaws with fine teeth provide accuracy and control.

Hand tools such as tin snips, scissors, or even a utility knife are useful for making small notches.

Additional tools

You will need a flat, stable workbench to work on.

To set guidelines, you will need a tape measure, a ruler, and a marking pen.

An air-compressor will help you remove chips that may have entered the sheets’ cells.

Question 31

What is the right saw for on-site cutting SUNLITE multiwall polycarbonate sheets?

Accepted Answer

Safety First: Protect yourself by using professional equipment, keeping your surroundings neat and tidy, and using tools with caution and care.

Power tools

Circular table saws are the most efficient and accurate way to cut plastic sheets. This option, however, isn't always available on home renovation sites.

A portable fine-toothed circular saw is ideal for cutting on-site. High blade speed and a moderate feeding rate will give you the most effective results.

A jigsaw also produces clean, accurate cuts, but requires better control. It is most suitable for cutting complex shapes and curved lines.

Manual tools

Working with manual tools is time-consuming, but it reduces the risk of sheet damage.

Manual handsaws or hacksaws with fine teeth provide accuracy and control.

Hand tools such as tin snips, scissors, or even a utility knife are useful for making small notches.

Additional tools

You will need a flat, stable workbench to work on.

To set guidelines, you will need a tape measure, a ruler, and a marking pen.

An air-compressor will help you remove chips that may have entered the sheets’ cells.

Question 32

How to cut and trim SUNLITE multiwall polycarbonate sheets on-site?

Accepted Answer

On-site tailoring and trimming of multiwall polycarbonate sheets is simple.

Follow these guidelines to ensure high-quality results.

Safety First: Protect yourself by using professional equipment, keeping your surroundings neat and tidy, and using tools with caution and care.

Place a piece of cardboard or plywood on the workbench under the polycarbonate sheet. This will protect the surface from scratches.

SUNLITE DIY sheets come with protective films. This film indicates which side of the panel is UV-protected. Do not remove it. You will need it later.

Measure the sheet, make pen marks at each end, and join the marks with a ruler.

Do not rush measuring and marking. You cannot patch the sheets together once they've been trimmed.

Secure the sheet to the workbench surface to prevent movement and vibrations.

Support the sheet near the cutting line by placing a timber plank on top of it, parallel to the markings.

Cut one sheet at a time.

Advance the saw slowly and steadily and do not stop once you have begun. It will ensure a clean, consistent edge.

Clean the sheet’s channels with compressed air.

Remove leftover cuts and scraps from the cutting table.

Question 33

What is the best polycarbonate panel for thermal properties and light transmission?

Accepted Answer

There is a trade-off between light transmission, transparency, and thermal properties in polycarbonate sheets. Multiwall polycarbonate sheets provide superior thermal insulation over solid sheets, but they are translucent, not transparent.

Clear polycarbonate panels will be fully transparent, but less thermally insulating.

Both options allow high light transmission, depending on their color.

If your main concern is light transmission, and not a glass-like appearance, you can achieve that with multiwall sheets, such as SUNLITE, or with the SUNPAL architectural multiwall panel system.

If your main concern is clarity, your best option is PALSUN solid polycarbonate sheets, or SUNGLAZE architectural solid panel system.

Another important factor to remember is that multi-wall sheets weigh significantly less than solid sheets. This can lower your construction and labor costs.

Question 34

What is the right roof pitch for SUNTUF and PALRUF corrugated plastic sheeting?

Accepted Answer

A proper slope keeps water off the roof. It prevents leaks, keeps the roof clean, and ensures structural integrity.

Roof slope percentage indicates how much the roof falls over a given distance. For example, the roof slope would be 5% if it dropped 5 centimeters over one meter.

DIY corrugated plastic sheet typically requires a 10% slope. Some profiles call for a deeper slope. Check the specs of your sheeting to be sure.

Pay attention: If you expect leaves or snow to accumulate on your roof, consider a deeper slope.

Question 35

Can polycarbonate light transmittance be degraded over time?

Accepted Answer

SUNTUF roofing sheets are made with a UV protection layer. This layer protects the sheets from UV radiation harm and maintains light transmittance and quality for many years.

Question 36

PALRUF PVC or SUNTUF polycarbonate corrugated sheets: when to use which?

Accepted Answer

PVC corrugated sheets are typically used in highly-corrosive environments such as port warehouses, cowsheds, and dairies for opaque roofing and siding. When natural daylight illumination is needed, polycarbonate corrugated sheets are used as roofing or siding.

Question 37

Can I step on SUNTUF skylights during or after installation?

Accepted Answer

Although SUNTUF is remarkably strong and can support extreme loads, for your safety, do not stand directly on the sheets. If it can’t be avoided, use stepping ladders, platforms or crawling boards.

Question 38

How to clean polycarbonate roofing?

Accepted Answer

Here are some steps to clean your polycarbonate roofing sheets:

Remove any loose debris, such as leaves or twigs, from the sheets surface using a broom or leaf blower.

Dip a soft cloth or sponge into a bucket of warm water and gently scrub the sheets, working in small sections at a time.

Rinse the sheets thoroughly with water to remove any remaining dirt or soap suds.

Dry the sheets with a clean and soft cloth, or allow them to air dry.

Avoid using high-pressure water or a pressure washer. High pressure can damage the sheets' surface.

Avoid using harsh chemicals or abrasive cleaners, as they can damage the sheets' surface. Before using a detergent, ensure it is polycarbonate-compliant.

If the sheets are particularly dirty or have stains that are difficult to remove, you may need to repeat the cleaning process a few times to get them fully clean.

In addition to cleaning the sheets, it is also worthwhile to regularly inspect the roofing for damage or wear.

Question 39

How do I combine SUNTUF rooflights or sidelights with corrugated metal roofing?

Accepted Answer

Palram's MetalMatch technology enables a precise match of corrugated SUNTUF to almost any industrial metal sheet. Contact your local Palram office for more details.

Question 40

What kind of gasket is suitable for corrugated SUNTUF and PALRUF sheets?

Accepted Answer

Flexible EPDM gaskets with metal washers.

Flexible EPDM gaskets allow just enough free movement for the sheets as they contract and expand. This ensures an effective seal against leaks and reduces stress and micro cracks. The metal washers will distribute the fastener load and will support the gasket.

Gaskets should conceal holes properly.

Use a 25mm gasket for a 10mm drill. A 19mm gasket is the alternative when the corrugation profile does not allow a wider gasket (if the valley or crest is too narrow).

Question 41

Which screws to use for fixing corrugated SUNTUF and PALRUF roofing sheets?

Accepted Answer

Use corrosion-resistant screws for optimal long-term service

Use screws with an outside thread diameter of ¼”

Screw shaft length varies with corrugation profile and fixing location (crest or valley).

Use self-tapping screws for timber purlins, and self-drilling screws for metal purlins.

Question 42

Why do polycarbonate roofing sheets require pre-drilling oversized holes?

Accepted Answer

Polycarbonate sheets are typically attached to support structures using screws or other fasteners. It is necessary to pre-drill oversized holes in the SUNTUF sheets to allow for expansion and contraction due to temperature changes. This is critical to ensuring the roof's quality and performance over time.

Question 43

How to accommodate SUNTUF polycarbonate roofing sheets' thermal expansion

Accepted Answer

Polycarbonate roofing sheets can accommodate thermal movement by following these guidelines:

Keep a small gap where the SUNTUF sheets meet another object. Sheets expand most along their length, so pay attention to this direction.

Pre-drill oversize holes around the fixings. In this way, the screws won't stress the sheets.

Polycarbonate ridge caps, wall connectors, and flashings should also be predrilled with oversized holes.

Applying foam tape along structural elements that come in contact with sheets will reduce friction noise.

Leave a 5cm-10cm overhang over the lower purlin.

Question 44

How many side overlaps does SUNTUF or PALRUF corrugates roofing require?

Accepted Answer

With a proper roof pitch, an overlap of one corrugation between sheets will keep the roof leak-safe, as long as the sheets are laid correctly.

Find the primary direction wind and rain are expected to come from and place the first sheet in the opposite direction. The next sheet will overlap the first, and so on. By doing so, you reduce the chance that water and dust will penetrate between the sheets.

Question 45

Which side of the SUNTUF roofing sheet should face up?

Accepted Answer

Look for a removable strip that indicates which side of the sheet is UV-protected.

It is critical to install the sheets with the UV-protected side facing up.

Remove the marking strip after installation.

Question 46

What is the recommended purlin spacing for SUNTUF corrugated polycarbonate roofs?

Accepted Answer

The required purlin spacing for corrugated polycarbonate roofing depends on a number of factors, including the size and type of corrugated sheets. In addition, the type of support structure, and local building codes.

Follow Palram's technical guidelines for the specific SUNTUF product you have chosen. This will ensure that the roofing is properly supported and able to withstand the loads and stresses it will be subjected to.

Question 47

Can SUNTUF corrugated polycarbonate or PALRUF PVC sheets be bent into arches?

Accepted Answer

Corrugated plastic sheets are tough and flexible. You can easily bend them to a curved roof without losing material integrity. There is only one rule: stay within the allowed arch radius.

In simple terms, an arc is a segment of a circle, and its radius is equal to its circle's radius.

Your sheet's minimum bending radius is determined by its profile (corrugation) and thickness.

Typical DIY polycarbonate corrugated sheets can bend to an arc radius of 4,000mm. Some of the more robust sheets require a minimum radius of 7,000mm. Check the specs of your sheeting to be sure.

Question 48

How to Install SUNTUF Corrugated Polycarbonate Roofing Sheets DIY

Accepted Answer

Specifications vary between different products and sheet profiles. Read the installation instructions for the specific roofing sheet you have chosen and follow them carefully.

Here is a general outline of the steps involved in installing corrugated polycarbonate roofing panels:

Have your roofing framework built, including rafters and purlins with appropriate spacing.

Measure and mark the area where the panels will be installed.

Trim the sheets to the right length, if needed.

Place the first panel on the roof and align it with the roof edge.

Before securing the panel to the roof frame, remember:

Place the fixings in the right places.

Use suitable screws and gaskets.

Pre-drill oversized holes to allow thermal movement.

Repeat the process with the remaining panels, overlapping and align them with the corrugations.

If needed, add additional flashing.

It is important to follow the manufacturer's installation instructions carefully and use the appropriate fasteners and sealants to ensure a secure and durable installation.

If you are unsure about how to install the panels or are not comfortable with the process, it is recommended to hire a professional contractor to do the job.

Question 49

How to Cut PALRUF Corrugated PVC Roofing Sheets DIY

Accepted Answer

Corrugated PVC sheets are popular for garden shed roofing and outdoor canopies. A durable solution that provides strength and resistance to moisture and chemicals. On-site tailoring and trimming is simple. Follow these guidelines to ensure professional results.

Safety First: Protect yourself by using professional equipment, keeping your surroundings neat and tidy, and using tools with caution and care.

Place a layer of cardboard or plywood on the workbench before placing the sheets. This will protect the surface from scratches.

Place the PVC panels on your workbench.

Clamp a few sheets together. This will reduce vibrations.

Use a measuring tape to measure the sheet, and make pen marks at each end. Join the marks with a ruler.

Do not rush measuring and marking. Once trimmed, you cannot patch the sheets together.

Secure the PVC sheets to the workbench surface to prevent movement and vibrations.

Support the sheets near the cutting line. You can do this by placing a timber plank on top of the sheets, parallel to the markings.

Cut along the marked pen line. The preferred method is to use a fine-tooth saw that rotates at high speed.

Advance the saw slowly and steadily and do not stop once you have begun. It will ensure a clean, consistent edge.

Remove leftover cuts and scraps from the cutting table.

Question 50

What Is the Right Saw for Cutting PALRUF Corrugated PVC Sheets?

Accepted Answer

Safety First: Protect yourself by using professional equipment, keeping your surroundings neat and tidy, and using tools with caution and care.

Power tools

Circular table saws are the most efficient and accurate way to cut plastic sheets. This option, however, is rarely available on home improvement sites.

A portable fine-toothed circular saw is ideal for cutting on-site. High blade speed and moderate feeding rate will give you the best results.

A jigsaw also produces clean, accurate cuts, but requires better control. It is most suitable for cutting complex shapes and curved lines

Manual tools

Working with manual tools is time-consuming, but it reduces the possibility of sheet damage.

Manual handsaws with fine teeth provide accuracy and control

Hand tools such as tin snips, scissors, or even a utility knife are useful when working with thin PVC sheets or making small notches.

Additional tools

You will need a flat, stable workbench to work on.

To set guidelines, you will need a tape measure, a ruler, and a marking pen.

Question 51

How to Cut SUNTUF Corrugated Polycarbonate Roofing Sheets DIY

Accepted Answer

Corrugated polycarbonate sheets are common roofing materials for DIY garden shelters and outdoor canopies. On-site tailoring and trimming is simple. Follow these guidelines to ensure quality results.

Safety First: Protect yourself by using professional equipment, keeping your surroundings neat and tidy, and using tools with caution and care.

Place a layer of cardboard or plywood on the workbench before placing the sheets. This will protect the surface from scratches.

Place the polycarbonate panels on your workbench.

Clamp a few sheets together. This will reduce vibrations.

Polycarbonate sheets come with a removable protective film or marking strip. This film indicates which side of the panel is UV-protected. Do not remove it. You will need it later.

Use a measuring tape to measure the sheet, and make pen marks at each end. Join the marks with a ruler.

Do not rush measuring and marking. Once trimmed, you cannot patch the sheets together.

Secure the polycarbonate sheets to the workbench surface to prevent movement and vibrations.

Support the sheets near the cutting line. You can do this by placing a timber plank on top of the sheets, parallel to the markings.

Cut along the marked pen line. The preferred method is to use a fine-tooth saw that rotates at high speed.

Advance the saw slowly and steadily and do not stop once you have begun. It will ensure a clean, consistent edge.

Remove leftover cuts and scraps from the cutting table.

Question 52

What Is the Right Saw for Cutting SUNTUF Corrugated Polycarbonate Sheets?

Accepted Answer

Safety First: Protect yourself by using professional equipment, keeping your surroundings neat and tidy, and using tools with caution and care.

Power tools

Circular table saws are the most efficient and accurate way to cut plastic sheets. This option, however, is rarely available on home improvement sites.

A portable fine-toothed circular saw is ideal for cutting on-site. High blade speed and moderate feeding rate will give you the best results.

A jigsaw also produces clean, accurate cuts, but requires better control. It is most suitable for cutting complex shapes and curved lines

Manual tools

Working with manual tools is time-consuming, but it reduces the possibility of sheet damage.

Manual handsaws with fine teeth provide accuracy and control.

Hand tools such as tin snips, scissors, or even a utility knife are useful when working with thin polycarbonate sheets or for making small notches.

Additional tools

You will need a flat, stable workbench to work on.

To set guidelines, you will need a tape measure, a ruler, and a marking pen.

Question 53

How to Store Polycarbonate Sheets

Accepted Answer

Polycarbonate sheets are tough and durable and guaranteed to last for years.

Here are some tips for storing polycarbonate sheets to ensure you get the most out of your investment.

Polycarbonate should be stored horizontally on a flat surface, such as a pallet or a shelf.

Ensure that no nails or bolts protrude from the platform. Even small rocks can leave permanent dents and scratches on the sheets.

Stack the largest sheets at the bottom, and the shorter, smaller panels on top.

Avoid stepping on polycarbonate panels and placing heavy or sharp equipment on them.

Store the polycarbonate sheet in a dry, cool, ventilated, shaded area away from direct sunlight.

Keep your stack dry to prevent whitening and water spots.

Avoid covering the sheets with dark films or other heat-absorbing materials.

Cover the panels with an opaque, bright, waterproof cover if you intend to leave them outdoors.

Question 54

What are three-dimensional or 3D logo signs?

Accepted Answer

3D letters and/or 3D logos are made of plastic, metal or foam. They reinforce an upscale image and create a clear highlighted message. These signs can be illuminated when required.

Question 55

How do I curve the polycarbonate to follow the façade curve?

Accepted Answer

All Palram polycarbonate products can be cold bent onsite during installation, subject to a minimum radius. The radius varies based on the chosen product. For flat sheets such as PALSUN & SUNLITE, the rule-of-thumb for the minimum radius is the thickness multiplied by 200. Please check the Palram catalog for more detailed specifications.

Question 56

How do I specify the required thickness of the polycarbonate glazing material?

Accepted Answer

The recommended thickness of the polycarbonate glazing material is based on factors such as wind & snow load, panel size, and boundary conditions. Visit the Palram website for access to calculators that can help you determine the recommended thickness.

Question 57

How do I reduce the heat build-up coming from the façade into the building?

Accepted Answer

In order to reduce heat build-up through the façade, Palram strongly recommends the use of its tinted SolarSmart™ panels. SolarSmart™ tints can be implemented in all Palram polycarbonate products. For more information, reference the Palram SolarSmart™ technology page.

Question 58

How do I create a double skin glazing solution for façades and curtain walls?

Accepted Answer

Flat solid or multiwall sheets can be glazed in double skin applications using standard aluminum curtain wall profiles and EPDM gaskets. The SUNPAL system can be installed in a double skin application with a special aluminum profile provided by Palram.

Question 59

Can flat solid polycarbonate be installed in a similar manner to glass in curtain wall applications?

Accepted Answer

PALSUN can be installed with standard curtain wall aluminum glazing profiles and EPDM gaskets (similar to glass), or spider fixing spaced with approximately 400 mm centers. However, it cannot be used with structural silicone and PALGARD (PALSUN) with anti-scratch coating is the recommended substitute in this case.

Question 60

Should products be pre-dried before thermoforming?

Accepted Answer

This depends on the production date and storage conditions of the product before thermoforming. It is recommended to check the product before thermoforming is attempted.

Question 61

Is the PE film suitable for thermoforming applications?

Accepted Answer

Most of Palram's products that are delivered with PE film covering are suitable for thermoforming. In general, we recommend using clear PE and not printed PE.

Question 62

How do I polish the edges of acrylic?

Accepted Answer

Acrylic edges can be polished by heating them with a torch, blowing hot air on them, or rotating a brush with wax.

Question 63

What is the minimum allowed bending radius of polycarbonate?

Accepted Answer

The minimum allowed bending radius of the polycarbonate is 200 times the thickness of the sheet, for example, a 2 mm sheet has a minimum 400 mm bending radius.

Question 64

What are the dimensions of PALCLAD Pro sheets (size and thickness)?

Accepted Answer

PALCLAD Pro comes in a standard size of 1500x3000 mm and in thicknesses of 2 and 2.5 mm.

Professional

Residential

Professional

Commercial

Residential

FREQUENTLY ASKED QUESTIONS

Question subject + -

Category + -

Product + -

Contact Us

Question subject + -

Category + -

Product + -

Contact Us

Palram South Africa uses cookies